Researchers at the University of Michigan have found a way to put a hemi into your next mobile phone. While it is not the legendary MOPAR Hemi engine, it is a hemispherical antenna. U of M researchers have figured out how to mass-produce antennas so small that they approach the fundamental minimum size limit for their bandwidth, or data rate, of operation according to the U of M News Service.
The antenna is typically the largest wireless component in mobile devices. Shrinking it could leave more room for other gadgets and features, Anthony Grbic, an associate professor in the Department of Electrical Engineering and Computer Science said.
Mr. Grbic and Stephen Forrest, a professor in the departments of Materials Science and Engineering and Physics, led the development of the hemisphere-shaped antennas, which can be manufactured with innovative imprint processing techniques that are rapid and low-cost. The finished product is 1.8 times the fundamental antenna size limit established in 1948 by L.J. Chu. The dimensions of this limit vary based on an antenna’s bandwidth.
“Ever since the Chu limit was established, people have been trying to reach it,” Mr. Grbic said in the article. “Standard printed circuit board antennas don’t come close. Some researchers have approached the limit with manually built antennas, but those are complicated and there’s no efficient way to manufacture them. We’ve found a way to cut the antenna’s size while maximizing its bandwidth, using a process that’s amenable to mass production.”
The researchers’ prototype operates at 1.5 gigahertz, in the frequency range of Wi-Fi devices as well as cordless and mobile phones. The antenna is 70 percent efficient and ten times smaller than conventional antennas, Mr. Grbic said. It has three times the conductivity of similar devices produced by 3-D ink-jet printing techniques, a process that serially writes the antenna geometry.
This new method is a very general process, said Carl Pfeiffer, a doctoral student in the Department of Electrical Engineering and Computer Science and first author of a paper on the work, “Novel Methods to Analyze and Fabricate Electrically Small Antennas” will be presented at the 2011 IEEE International Symposium on Antennas and Propagation.
“It can be used to fabricate antennas that are of a wide variety of sizes, shapes, frequencies, and designs,” Mr. Pfeiffer said. “Basically if you tell me the data rate that is required for a particular application, I can make an antenna that does this while at the same time being as small as possible.”
The prototype was made in the College of Engineering’s Lurie Nanofabrication Facility. The work was funded by the Department of Education’s Graduate Assistance in Areas of National Need program, the National Science Foundation, and the U.S. Air Force Office of Scientific Research.
The researchers believe this development could lead to new generations of wireless consumer electronics and mobile phones that are either smaller or can perform more functions. Beyond consumer electronics, this work could be useful in wireless sensing and military communications. Wireless sensor networks could be used for environmental monitoring or surveillance.
rb-
Like the Chrysler Hemi, these new antennas may supercharge mobile phones. The small size could allow multiple antennas to be built into mobile devices allowing MIMO connections. The small size should also cut down on the power requirements, decreasing the size of the battery required and increasing the time between charges.
Related articles
Ralph Bach has been in IT long enough to know better and has blogged from his Bach Seat about IT, careers, and anything else that catches his attention since 2005. You can follow him on LinkedIn, Facebook, and Twitter. Email the Bach Seat here.
Cisco‘s (CSCO) two consecutive under-performing quarters finally prompted CEO John Chambers to take action. One of the first actions Cisco will undertake during reorganization is to sell a set-top box manufacturing plant in Juarez, Mexico. FierceEnterpriseCommunications reports that Cisco will sell the plant to Foxconn Technology Group, The plant has about 5,000 workers who likely will remain as employees of Terry Gou according to FierceEnterpriseCommunications.
In addition, the embattled CEO vowed $1 billion in cuts this year to Cisco’s expenses. Mr. Chambers announced plans to cut its workforce by 11,500. Cisco said about 975, or 15 percent, would be executives with job titles of vice president or above. A Cisco spokesperson said the employee reductions announced would be enough to reach the $1 billion cost-cutting target Chambers set in May.
Gleacher & Co. analyst Brian Marshall told FierceEnterpriseCommunications that the staff reductions were a good first step for Cisco, but he added that the remaining questions, e.g. how Cisco would fix the top line and drive revenue growth and product innovations, need answers.
Despite the widespread success of the 
Loading ...
The 
